Czy dysk jest wadliwy

[korfanty33]

0

Witam wszystkich

Znalazłem starego Dell'a i postawiłem na nim dwa systemy w tym Mint 'a .

Strasznie mi dysk rzęzi .

Odinstalowałem DropBoxa prze-boot-owałem system .

Trochę pomogło , ale mój angielski jest słaby bo pojawiły się błędy dysku .
Po zainstalowaniu programu

sudo apt  GSmartControl

listing

Kod:

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-32-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint T166
Device Model:     SAMSUNG HD321KJ
Serial Number:    S0MQJ9DQ603011
LU WWN Device Id: 5 0000f0 09b603011
Firmware Version: CP100-13
User Capacity:    319,936,615,424 bytes [319 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 3b
SATA Version is:  SATA 2.5, 3.0 Gb/s
Local Time is:    Sun Jun  7 00:12:11 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         ( 5768) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      (  99) minutes.
SCT capabilities:            (0x003f)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   051    -    0
  3 Spin_Up_Time            POS---   100   100   015    -    5504
  4 Start_Stop_Count        -O--CK   097   097   000    -    3967
  5 Reallocated_Sector_Ct   PO--CK   253   253   010    -    0
  7 Seek_Error_Rate         POSR--   253   253   051    -    0
  8 Seek_Time_Performance   P-S--K   253   253   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    3121
10 Spin_Retry_Count        PO--CK   253   253   051    -    0
11 Calibration_Retry_Count -O--C-   253   253   000    -    0
12 Power_Cycle_Count       -O--CK   097   097   000    -    3273
13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    1148040
187 Reported_Uncorrect      -O--CK   087   087   000    -    14
188 Command_Timeout         -O--CK   100   100   000    -    25
190 Airflow_Temperature_Cel -O---K   063   061   000    -    37
194 Temperature_Celsius     -O---K   124   121   000    -    38
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    1148040
196 Reallocated_Event_Count -O--CK   253   253   000    -    0
197 Total_Pending_Sectors   -O--C-   253   100   000    -    0
198 Offline_Uncorrectable   ----CK   253   253   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
200 Multi_Zone_Error_Rate   -O-R--   100   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   100   000    -    0
202 Data_Address_Mark_Errs  -O--CK   100   100   000    -    23
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Invalid Error Log index = 0x0000, trying reserved byte (0x06) instead
Device Error Count: 486 (device log contains only the most recent 8 errors)
    CR     = Command Register
    FEATR  = Features Register
    COUNT  = Count (was: Sector Count) Register
    LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
    LH     = LBA High (was: Cylinder High) Register    ]   LBA
    LM     = LBA Mid (was: Cylinder Low) Register      ] Register
    LL     = LBA Low (was: Sector Number) Register     ]
    DV     = Device (was: Device/Head) Register
    DC     = Device Control Register
    ER     = Error register
    ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 486 [5] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 01 00 00 00 61 5d 81 e0 00  Error: UNC at LBA = 0x00615d81 = 6380929

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 01 00 00 00 61 5d 81 e0 00     00:22:13.500  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:13.500  READ DMA EXT

Error 485 [4] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 02 00 00 00 61 5d 81 e0 00  Error: UNC at LBA = 0x00615d81 = 6380929

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 02 00 00 00 61 5d 81 e0 00     00:22:07.313  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 02 00 00 00 61 5d 7f e0 00     00:22:07.313  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 0f de 94 7d e0 00     00:22:07.313  READ DMA EXT
  42 ff ff 00 04 00 00 00 61 5d 83 e0 00     00:22:07.313  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:07.313  READ DMA EXT

Error 484 [3] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 04 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 04 00 00 00 61 5d 7f e0 00     00:22:02.125  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:02.125  READ DMA EXT
  42 ff ff 00 08 00 00 00 61 5d 87 e0 00     00:22:02.125  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:02.125  READ DMA EXT

Error 483 [2] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 08 00 00 00 61 5d 7f e0 00     00:21:56.000  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 10 00 00 00 61 5d 8f e0 00     00:21:55.938  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 0f de 94 7d e0 00     00:21:55.938  READ DMA EXT

Error 482 [1] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 10 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 10 00 00 00 61 5d 7f e0 00     00:21:50.750  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:50.750  READ DMA EXT
  42 ff ff 00 20 00 00 00 61 5d 9f e0 00     00:21:50.750  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:50.750  READ DMA EXT

Error 481 [0] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 20 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 20 00 00 00 61 5d 7f e0 00     00:21:45.875  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:45.875  READ DMA EXT

Error 480 [7] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 40 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 40 00 00 00 61 5d 7f e0 00     00:21:41.375  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 40 00 00 00 61 5d 3f e0 00     00:21:41.375  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 80 00 00 00 61 5d bf e0 00     00:21:41.313  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 0f de 94 7d e0 00     00:21:41.313  READ DMA EXT

Error 479 [6] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 80 00 00 00 61 5d 3f e0 00  Error: UNC at LBA = 0x00615d3f = 6380863

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 80 00 00 00 61 5d 3f e0 00     00:21:36.438  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:36.438  READ DMA EXT

SMART Extended Self-test Log (GP Log 0x07) not supported

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    38 Celsius
Power Cycle Min/Max Temperature:     37/38 Celsius
Lifetime    Min/Max Temperature:      3/38 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (68)

Index    Estimated Time   Temperature Celsius
  69    2020-06-06 22:05    35  ****************
...    ..(  6 skipped).    ..  ****************
  76    2020-06-06 22:12    35  ****************
  77    2020-06-06 22:13    36  *****************
  78    2020-06-06 22:14    36  *****************
  79    2020-06-06 22:15    36  *****************
  80    2020-06-06 22:16    35  ****************
...    ..(  2 skipped).    ..  ****************
  83    2020-06-06 22:19    35  ****************
  84    2020-06-06 22:20    36  *****************
  85    2020-06-06 22:21    35  ****************
...    ..(  9 skipped).    ..  ****************
  95    2020-06-06 22:31    35  ****************
  96    2020-06-06 22:32    36  *****************
  97    2020-06-06 22:33    36  *****************
  98    2020-06-06 22:34    35  ****************
  99    2020-06-06 22:35    35  ****************
100    2020-06-06 22:36    36  *****************
...    ..(  2 skipped).    ..  *****************
103    2020-06-06 22:39    36  *****************
104    2020-06-06 22:40    35  ****************
...    ..(  3 skipped).    ..  ****************
108    2020-06-06 22:44    35  ****************
109    2020-06-06 22:45    36  *****************
110    2020-06-06 22:46    36  *****************
111    2020-06-06 22:47    35  ****************
...    ..(  4 skipped).    ..  ****************
116    2020-06-06 22:52    35  ****************
117    2020-06-06 22:53    36  *****************
118    2020-06-06 22:54    35  ****************
119    2020-06-06 22:55    35  ****************
120    2020-06-06 22:56    35  ****************
121    2020-06-06 22:57    36  *****************
122    2020-06-06 22:58    35  ****************
...    ..( 38 skipped).    ..  ****************
  33    2020-06-06 23:37    35  ****************
  34    2020-06-06 23:38    33  **************
  35    2020-06-06 23:39    38  *******************
...    ..( 13 skipped).    ..  *******************
  49    2020-06-06 23:53    38  *******************
  50    2020-06-06 23:54    37  ******************
  51    2020-06-06 23:55    38  *******************
...    ..(  2 skipped).    ..  *******************
  54    2020-06-06 23:58    38  *******************
  55    2020-06-06 23:59    37  ******************
  56    2020-06-07 00:00    38  *******************
...    ..( 10 skipped).    ..  *******************
  67    2020-06-07 00:11    38  *******************
  68    2020-06-07 00:12    35  ****************

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8001  2            0  Vendor specific

Cz dysk się kończy ??

[dedito]

0

Dysk wygląda w porządku.
Jedynie wysoka wartość 13 dziwna i na dodatek taka sama jak 195.

[korfanty33]

0

Dysk wygląda w porządku.
Jedynie wysoka wartość 13 dziwna i na dodatek taka sama jak 195.

Kod:

13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    1148040
....
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    1148040

Kod:

                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

Dziś wziełem drugi dysk postawiłem taką samą konfigurację . Zaraz zobaczę czy jest podobnie ?
jest trochę inny 

Kod:

sudo apt-get install -y gsmartcontrol

Kod:

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-32-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint M7E (AF)
Device Model:     SAMSUNG HM321HI
Serial Number:    S2HZJ9BB308656
LU WWN Device Id: 5 0024e9 204bff6b7
Firmware Version: 2AJ10002
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Sun Jun  7 16:42:53 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM level is:     254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (  25)    The self-test routine was aborted by
                    the host.
Total time to complete Offline
data collection:         ( 4680) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      (  78) minutes.
SCT capabilities:            (0x003f)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   100   100   051    -    1
  2 Throughput_Performance  -OS--K   252   252   000    -    0
  3 Spin_Up_Time            PO---K   089   089   025    -    3411
  4 Start_Stop_Count        -O--CK   097   097   000    -    3622
  5 Reallocated_Sector_Ct   PO--CK   252   252   010    -    0
  7 Seek_Error_Rate         -OSR-K   252   252   051    -    0
  8 Seek_Time_Performance   --S--K   252   252   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    6062
10 Spin_Retry_Count        -O--CK   252   252   051    -    0
11 Calibration_Retry_Count -O--CK   100   100   000    -    145
12 Power_Cycle_Count       -O--CK   097   097   000    -    3592
181 Program_Fail_Cnt_Total  -O---K   099   099   000    -    39007714
191 G-Sense_Error_Rate      -O---K   100   100   000    -    3228
192 Power-Off_Retract_Count -O---K   252   252   000    -    0
194 Temperature_Celsius     -O----   064   042   000    -    31 (Min/Max 14/58)
195 Hardware_ECC_Recovered  -O-RCK   100   100   000    -    0
196 Reallocated_Event_Count -O--CK   252   252   000    -    0
197 Current_Pending_Sector  -O--CK   252   252   000    -    0
198 Offline_Uncorrectable   ----CK   252   252   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   -O-R-K   100   100   000    -    62
223 Load_Retry_Count        -O--CK   100   100   000    -    145
225 Load_Cycle_Count        -O--CK   091   091   000    -    94211
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 4
    CR     = Command Register
    FEATR  = Features Register
    COUNT  = Count (was: Sector Count) Register
    LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
    LH     = LBA High (was: Cylinder High) Register    ]   LBA
    LM     = LBA Mid (was: Cylinder Low) Register      ] Register
    LL     = LBA Low (was: Sector Number) Register     ]
    DV     = Device (was: Device/Head) Register
    DC     = Device Control Register
    ER     = Error register
    ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4 [3] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.165  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.165  READ DMA EXT
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT

Error 3 [2] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF 1 sectors at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.165  READ DMA EXT
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 08 00 e0 00     00:00:00.159  READ DMA EXT

Error 2 [1] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 08 00 e0 00     00:00:00.159  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 00 00 e0 00     00:00:00.159  READ DMA EXT

Error 1 [0] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF 1 sectors at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 08 00 e0 00     00:00:00.159  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 00 00 e0 00     00:00:00.159  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 00 00 e0 00     00:00:00.159  READ DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Aborted by host               90%      5589         -
# 2  Short offline       Completed without error       00%      5589         -
# 3  Short offline       Completed without error       00%      5323         -
# 4  Short offline       Completed without error       00%      5323         -
# 5  Short offline       Completed without error       00%      4741         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Aborted_by_host [90% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    31 Celsius
Power Cycle Min/Max Temperature:     31/33 Celsius
Lifetime    Min/Max Temperature:     14/59 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         5 minutes
Temperature Logging Interval:        5 minutes
Min/Max recommended Temperature:     -5/80 Celsius
Min/Max Temperature Limit:           -10/85 Celsius
Temperature History Size (Index):    128 (90)

Index    Estimated Time   Temperature Celsius
  91    2020-06-07 06:05    31  ************
  92    2020-06-07 06:10    29  **********
...    ..(  2 skipped).    ..  **********
  95    2020-06-07 06:25    29  **********
  96    2020-06-07 06:30    30  ***********
  97    2020-06-07 06:35    31  ************
  98    2020-06-07 06:40    29  **********
  99    2020-06-07 06:45    30  ***********
100    2020-06-07 06:50    30  ***********
101    2020-06-07 06:55    29  **********
102    2020-06-07 07:00    29  **********
103    2020-06-07 07:05    29  **********
104    2020-06-07 07:10    30  ***********
105    2020-06-07 07:15    31  ************
106    2020-06-07 07:20    31  ************
107    2020-06-07 07:25    30  ***********
108    2020-06-07 07:30    29  **********
109    2020-06-07 07:35    28  *********
110    2020-06-07 07:40    28  *********
111    2020-06-07 07:45    27  ********
112    2020-06-07 07:50    27  ********
113    2020-06-07 07:55    27  ********
114    2020-06-07 08:00    26  *******
115    2020-06-07 08:05    26  *******
116    2020-06-07 08:10    27  ********
117    2020-06-07 08:15    29  **********
...    ..(  2 skipped).    ..  **********
120    2020-06-07 08:30    29  **********
121    2020-06-07 08:35    28  *********
122    2020-06-07 08:40    30  ***********
123    2020-06-07 08:45    29  **********
124    2020-06-07 08:50    29  **********
125    2020-06-07 08:55    29  **********
126    2020-06-07 09:00    28  *********
...    ..(  2 skipped).    ..  *********
   1    2020-06-07 09:15    28  *********
   2    2020-06-07 09:20    30  ***********
   3    2020-06-07 09:25    31  ************
   4    2020-06-07 09:30    30  ***********
   5    2020-06-07 09:35    30  ***********
   6    2020-06-07 09:40    29  **********
   7    2020-06-07 09:45    28  *********
   8    2020-06-07 09:50    27  ********
   9    2020-06-07 09:55    28  *********
  10    2020-06-07 10:00    29  **********
  11    2020-06-07 10:05    29  **********
  12    2020-06-07 10:10    28  *********
  13    2020-06-07 10:15    29  **********
  14    2020-06-07 10:20    29  **********
  15    2020-06-07 10:25    29  **********
  16    2020-06-07 10:30    30  ***********
  17    2020-06-07 10:35    29  **********
...    ..(  2 skipped).    ..  **********
  20    2020-06-07 10:50    29  **********
  21    2020-06-07 10:55    28  *********
...    ..(  3 skipped).    ..  *********
  25    2020-06-07 11:15    28  *********
  26    2020-06-07 11:20    29  **********
  27    2020-06-07 11:25    29  **********
  28    2020-06-07 11:30    28  *********
  29    2020-06-07 11:35    29  **********
...    ..(  4 skipped).    ..  **********
  34    2020-06-07 12:00    29  **********
  35    2020-06-07 12:05    30  ***********
  36    2020-06-07 12:10    30  ***********
  37    2020-06-07 12:15    30  ***********
  38    2020-06-07 12:20    31  ************
  39    2020-06-07 12:25    31  ************
  40    2020-06-07 12:30    30  ***********
  41    2020-06-07 12:35    29  **********
...    ..(  4 skipped).    ..  **********
  46    2020-06-07 13:00    29  **********
  47    2020-06-07 13:05    30  ***********
  48    2020-06-07 13:10    29  **********
...    ..( 17 skipped).    ..  **********
  66    2020-06-07 14:40    29  **********
  67    2020-06-07 14:45    30  ***********
  68    2020-06-07 14:50    30  ***********
  69    2020-06-07 14:55    30  ***********
  70    2020-06-07 15:00    31  ************
  71    2020-06-07 15:05    31  ************
  72    2020-06-07 15:10    29  **********
  73    2020-06-07 15:15    31  ************
  74    2020-06-07 15:20    31  ************
  75    2020-06-07 15:25    33  **************
  76    2020-06-07 15:30    33  **************
  77    2020-06-07 15:35    33  **************
  78    2020-06-07 15:40    32  *************
  79    2020-06-07 15:45    32  *************
  80    2020-06-07 15:50    33  **************
  81    2020-06-07 15:55    34  ***************
  82    2020-06-07 16:00    33  **************
  83    2020-06-07 16:05    34  ***************
  84    2020-06-07 16:10    33  **************
  85    2020-06-07 16:15    32  *************
  86    2020-06-07 16:20    34  ***************
  87    2020-06-07 16:25    34  ***************
  88    2020-06-07 16:30    34  ***************
  89    2020-06-07 16:35    32  *************
  90    2020-06-07 16:40    32  *************

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x0007  4            0  R_ERR response for host-to-device non-data FIS
0x0008  4            0  Device-to-host non-data FIS retries
0x0009  4            2  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            2  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS
0x000f  4            0  R_ERR response for host-to-device data FIS, CRC
0x0010  4            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  4            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  4            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00  4            0  Vendor specific
0x8e01  4            0  Vendor specific
0x8e02  4            0  Vendor specific
0x8e03  4            0  Vendor specific
0x8e04  4            0  Vendor specific
0x8e05  4            0  Vendor specific
0x8e06  4            0  Vendor specific
0x8e07  4            0  Vendor specific
0x8e08  4            0  Vendor specific
0x8e09  4            0  Vendor specific
0x8e0a  4            0  Vendor specific
0x8e0b  4            0  Vendor specific
0x8e0c  4            0  Vendor specific
0x8e0d  4            0  Vendor specific
0x8e0e  4            0  Vendor specific
0x8e0f  4            0  Vendor specific
0x8e10  4            0  Vendor specific
0x8e11  4            0  Vendor specific

[dedito]

0

Ten też wygląda w porządku.

[morfik]

1

Mi tam nie wygląda w porządku -- są bady i sra błędami z tego powodu. Do tego dysk startuje ponad 5s, to nie za dobrze świadczy o mechanizmie obracającym talerzami. Na moje oko dysk do wywalenia. :]

[korfanty33]

0

Mi tam nie wygląda w porządku -- są bady i sra błędami z tego powodu. Do tego dysk startuje ponad 5s, to nie za dobrze świadczy o mechanizmie obracającym talerzami. Na moje oko dysk do wywalenia. :]

Ktury ?
Są dwa samsungi ,  pierwszy 3,5" na pewno jest popsuty .
Ale czy można na nim pracować choć trochę .

A drugi 2,5" samsung powinien być ok choć ma ponad 10 lat .

[morfik]

0

No ten S0MQJ9DQ603011 jest uszkodzony. Z kolei ten S2HZJ9BB308656 on miał jakieś błędy od samego początku pracy, choć widać trochę się to uspokoiło ale test całej powierzchni by się przydał. Póki co ten test co był został przerwany przez host'a co nie świadczy za dobrze. Trzeba go ponowić i zobaczyć czy jeszcze raz się wyłoży, jeśli tak, to dysk na gwarancję oddać jeśli jeszcze ma.

[dedito]

0

Mówisz Morfik, że na tym pierwszym dysku 13 i 195 wskazuje, że na dysku są badsectory?

[morfik]

0

Raczej ten 187 (Reported_Uncorrect ). Te 13 i 192 to one mają pewnie wartości, które trzeba wyliczyć z jakichś wzorów, także ja tam nie znam się na smart producentów, którzy nie przestrzegają standardów. Trzeba by poszukać za tymi atrybutami. Faktem jest, że w logu jest pełno błędów typu: Error: UNC at LBA, a to zwykle oznacza bad'a.

[dedito]

0

Ok, a ten spinuptime to trzyma ostatnią największą wartość, czy się zmienia przy każdym rozruchu dysku?