Ocena wątku:
  • 0 głosów - średnia: 0
  • 1
  • 2
  • 3
  • 4
  • 5
Czy dysk jest wadliwy
#11
0
To jest 10 letni dysk

Kod:
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-32-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint M7E (AF)
Device Model:     SAMSUNG HM321HI
Serial Number:    S2HZJ9BB308656
LU WWN Device Id: 5 0024e9 204bff6b7
Firmware Version: 2AJ10002
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Tue Jun  9 20:52:08 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM level is:     254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         ( 4680) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      (  78) minutes.
SCT capabilities:            (0x003f)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   100   100   051    -    1
  2 Throughput_Performance  -OS--K   252   252   000    -    0
  3 Spin_Up_Time            PO---K   089   089   025    -    3416
  4 Start_Stop_Count        -O--CK   097   097   000    -    3635
  5 Reallocated_Sector_Ct   PO--CK   252   252   010    -    0
  7 Seek_Error_Rate         -OSR-K   252   252   051    -    0
  8 Seek_Time_Performance   --S--K   252   252   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    6080
10 Spin_Retry_Count        -O--CK   252   252   051    -    0
11 Calibration_Retry_Count -O--CK   100   100   000    -    145
12 Power_Cycle_Count       -O--CK   097   097   000    -    3606
181 Program_Fail_Cnt_Total  -O---K   099   099   000    -    39041609
191 G-Sense_Error_Rate      -O---K   100   100   000    -    3229
192 Power-Off_Retract_Count -O---K   252   252   000    -    0
194 Temperature_Celsius     -O----   064   042   000    -    29 (Min/Max 14/58)
195 Hardware_ECC_Recovered  -O-RCK   100   100   000    -    0
196 Reallocated_Event_Count -O--CK   252   252   000    -    0
197 Current_Pending_Sector  -O--CK   252   252   000    -    0
198 Offline_Uncorrectable   ----CK   252   252   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   -O-R-K   100   100   000    -    82
223 Load_Retry_Count        -O--CK   100   100   000    -    145
225 Load_Cycle_Count        -O--CK   091   091   000    -    94419
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 4
    CR     = Command Register
    FEATR  = Features Register
    COUNT  = Count (was: Sector Count) Register
    LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
    LH     = LBA High (was: Cylinder High) Register    ]   LBA
    LM     = LBA Mid (was: Cylinder Low) Register      ] Register
    LL     = LBA Low (was: Sector Number) Register     ]
    DV     = Device (was: Device/Head) Register
    DC     = Device Control Register
    ER     = Error register
    ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4 [3] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.165  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.165  READ DMA EXT
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT

Error 3 [2] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF 1 sectors at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.165  READ DMA EXT
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 08 00 e0 00     00:00:00.159  READ DMA EXT

Error 2 [1] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  24 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ SECTOR(S) EXT
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 08 00 e0 00     00:00:00.159  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 00 00 e0 00     00:00:00.159  READ DMA EXT

Error 1 [0] occurred at disk power-on lifetime: 139 hours (5 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 01 00 00 25 43 15 81 e0 00  Error: IDNF 1 sectors at LBA = 0x25431581 = 625153409

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 ff 00 01 00 00 25 43 15 81 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 03 28 00 e0 00     00:00:00.160  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 08 00 e0 00     00:00:00.159  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 00 00 e0 00     00:00:00.159  READ DMA EXT
  25 00 ff 00 01 00 00 00 00 00 00 e0 00     00:00:00.159  READ DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      6080         -
# 2  Extended offline    Aborted by host               90%      5589         -
# 3  Short offline       Completed without error       00%      5589         -
# 4  Short offline       Completed without error       00%      5323         -
# 5  Short offline       Completed without error       00%      5323         -
# 6  Short offline       Completed without error       00%      4741         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    29 Celsius
Power Cycle Min/Max Temperature:     24/29 Celsius
Lifetime    Min/Max Temperature:     14/59 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         5 minutes
Temperature Logging Interval:        5 minutes
Min/Max recommended Temperature:     -5/80 Celsius
Min/Max Temperature Limit:           -10/85 Celsius
Temperature History Size (Index):    128 (22)

Index    Estimated Time   Temperature Celsius
  23    2020-06-09 10:15    29  **********
  24    2020-06-09 10:20    24  *****
  25    2020-06-09 10:25    24  *****
  26    2020-06-09 10:30    24  *****
  27    2020-06-09 10:35    25  ******
  28    2020-06-09 10:40    25  ******
  29    2020-06-09 10:45    25  ******
  30    2020-06-09 10:50    24  *****
  31    2020-06-09 10:55    24  *****
  32    2020-06-09 11:00    25  ******
  33    2020-06-09 11:05    24  *****
...    ..(  2 skipped).    ..  *****
  36    2020-06-09 11:20    24  *****
  37    2020-06-09 11:25    26  *******
  38    2020-06-09 11:30    29  **********
  39    2020-06-09 11:35    31  ************
  40    2020-06-09 11:40    31  ************
  41    2020-06-09 11:45    28  *********
  42    2020-06-09 11:50    28  *********
  43    2020-06-09 11:55    27  ********
  44    2020-06-09 12:00    29  **********
  45    2020-06-09 12:05    30  ***********
  46    2020-06-09 12:10    29  **********
  47    2020-06-09 12:15    29  **********
  48    2020-06-09 12:20    30  ***********
  49    2020-06-09 12:25    31  ************
  50    2020-06-09 12:30    29  **********
  51    2020-06-09 12:35    28  *********
  52    2020-06-09 12:40    27  ********
  53    2020-06-09 12:45    28  *********
...    ..(  2 skipped).    ..  *********
  56    2020-06-09 13:00    28  *********
  57    2020-06-09 13:05    31  ************
  58    2020-06-09 13:10    29  **********
  59    2020-06-09 13:15    29  **********
  60    2020-06-09 13:20    29  **********
  61    2020-06-09 13:25    30  ***********
  62    2020-06-09 13:30    31  ************
  63    2020-06-09 13:35    31  ************
  64    2020-06-09 13:40    32  *************
  65    2020-06-09 13:45    31  ************
  66    2020-06-09 13:50    31  ************
  67    2020-06-09 13:55    30  ***********
  68    2020-06-09 14:00    29  **********
  69    2020-06-09 14:05    29  **********
  70    2020-06-09 14:10    31  ************
  71    2020-06-09 14:15    33  **************
  72    2020-06-09 14:20    32  *************
  73    2020-06-09 14:25    31  ************
  74    2020-06-09 14:30    30  ***********
  75    2020-06-09 14:35    29  **********
  76    2020-06-09 14:40    29  **********
  77    2020-06-09 14:45    31  ************
  78    2020-06-09 14:50    30  ***********
  79    2020-06-09 14:55    29  **********
  80    2020-06-09 15:00    29  **********
  81    2020-06-09 15:05    28  *********
...    ..(  5 skipped).    ..  *********
  87    2020-06-09 15:35    28  *********
  88    2020-06-09 15:40    27  ********
...    ..( 10 skipped).    ..  ********
  99    2020-06-09 16:35    27  ********
100    2020-06-09 16:40    24  *****
101    2020-06-09 16:45    26  *******
...    ..(  2 skipped).    ..  *******
104    2020-06-09 17:00    26  *******
105    2020-06-09 17:05    27  ********
106    2020-06-09 17:10    27  ********
107    2020-06-09 17:15    27  ********
108    2020-06-09 17:20    28  *********
109    2020-06-09 17:25    28  *********
110    2020-06-09 17:30    28  *********
111    2020-06-09 17:35    30  ***********
112    2020-06-09 17:40    31  ************
113    2020-06-09 17:45    30  ***********
114    2020-06-09 17:50    30  ***********
115    2020-06-09 17:55    29  **********
...    ..( 12 skipped).    ..  **********
   0    2020-06-09 19:00    29  **********
   1    2020-06-09 19:05    28  *********
   2    2020-06-09 19:10    28  *********
   3    2020-06-09 19:15    28  *********
   4    2020-06-09 19:20    29  **********
   5    2020-06-09 19:25    29  **********
   6    2020-06-09 19:30    28  *********
   7    2020-06-09 19:35    29  **********
...    ..(  3 skipped).    ..  **********
  11    2020-06-09 19:55    29  **********
  12    2020-06-09 20:00    26  *******
  13    2020-06-09 20:05    26  *******
  14    2020-06-09 20:10    27  ********
  15    2020-06-09 20:15    27  ********
  16    2020-06-09 20:20    27  ********
  17    2020-06-09 20:25    28  *********
...    ..(  4 skipped).    ..  *********
  22    2020-06-09 20:50    28  *********

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x0007  4            0  R_ERR response for host-to-device non-data FIS
0x0008  4            0  Device-to-host non-data FIS retries
0x0009  4            2  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            2  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS
0x000f  4            0  R_ERR response for host-to-device data FIS, CRC
0x0010  4            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  4            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  4            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00  4            0  Vendor specific
0x8e01  4            0  Vendor specific
0x8e02  4            0  Vendor specific
0x8e03  4            0  Vendor specific
0x8e04  4            0  Vendor specific
0x8e05  4            0  Vendor specific
0x8e06  4            0  Vendor specific
0x8e07  4            0  Vendor specific
0x8e08  4            0  Vendor specific
0x8e09  4            0  Vendor specific
0x8e0a  4            0  Vendor specific
0x8e0b  4            0  Vendor specific
0x8e0c  4            0  Vendor specific
0x8e0d  4            0  Vendor specific
0x8e0e  4            0  Vendor specific
0x8e0f  4            0  Vendor specific
0x8e10  4            0  Vendor specific
0x8e11  4            0  Vendor specific
Odpowiedz


Skocz do:




Użytkownicy przeglądający ten wątek: 2 gości