Dwa Minty na dwóch dyskach - problem z uruchomieniem

[rivulek]

0

Ogólnie już wczoraj zmieniałem kabel i port (kabel zasilający też był inny) i nie widziałem żadnyc zmian. Teraz mzieniłem z powrotem tak jak było i nie widzę żadnych różnic. Wrzucam test:

Kod:

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-76-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     KINGSTON SUV500120G
Serial Number:    50026B76827524C0
LU WWN Device Id: 5 0026b7 6827524c0
Firmware Version: 003056RI
User Capacity:    120 034 123 776 bytes [120 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   Unknown(0x0ffe), ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sat Feb  1 12:27:01 2020 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (    5) seconds.
Offline data collection
capabilities: (0x71) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: (   2) minutes.
Extended self-test routine
recommended polling time: (   5) minutes.
Conveyance self-test routine
recommended polling time: (   0) minutes.
SCT capabilities:        (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 48
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   100   000    Pre-fail  Always       -       65359
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       1975
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       744
100 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       451728
101 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       111592
170 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
171 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
172 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
174 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       176
175 Program_Fail_Count_Chip 0x0032   100   100   000    Old_age   Always       -       0
176 Erase_Fail_Count_Chip   0x0032   100   100   000    Old_age   Always       -       0
177 Wear_Leveling_Count     0x0032   098   098   000    Old_age   Always       -       627
178 Used_Rsvd_Blk_Cnt_Chip  0x0002   100   100   000    Old_age   Always       -       0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0002   100   100   000    Old_age   Always       -       361
183 Runtime_Bad_Block       0x0032   098   098   000    Old_age   Always       -       10
187 Reported_Uncorrect      0x0033   100   100   000    Pre-fail  Always       -       0
194 Temperature_Celsius     0x0022   032   100   000    Old_age   Always       -       32 (Min/Max 22/42)
195 Hardware_ECC_Recovered  0x0032   100   100   000    Old_age   Always       -       65359
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
199 UDMA_CRC_Error_Count    0x0012   100   100   000    Old_age   Always       -       0
201 Unknown_SSD_Attribute   0x0032   100   100   000    Old_age   Always       -       0
204 Soft_ECC_Correction     0x0032   100   100   000    Old_age   Always       -       65359
231 Temperature_Celsius     0x0032   098   098   000    Old_age   Always       -       2
233 Media_Wearout_Indicator 0x0032   100   100   000    Old_age   Always       -       1512
234 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       1244
241 Total_LBAs_Written      0x0032   100   100   000    Old_age   Always       -       1189
242 Total_LBAs_Read         0x0032   100   100   000    Old_age   Always       -       1341
250 Read_Error_Retry_Rate   0x0032   100   100   000    Old_age   Always       -       65359

SMART Error Log Version: 0
No Errors Logged

SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision number = 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      1975         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Jeszcze odświeżone testy smart po długim skanowaniu: