Czy dysk jest wadliwy

[korfanty33]

0

Witam wszystkich

Znalazłem starego Dell'a i postawiłem na nim dwa systemy w tym Mint 'a .

Strasznie mi dysk rzęzi .

Odinstalowałem DropBoxa prze-boot-owałem system .

Trochę pomogło , ale mój angielski jest słaby bo pojawiły się błędy dysku .
Po zainstalowaniu programu

sudo apt  GSmartControl

listing

Kod:

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-32-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint T166
Device Model:     SAMSUNG HD321KJ
Serial Number:    S0MQJ9DQ603011
LU WWN Device Id: 5 0000f0 09b603011
Firmware Version: CP100-13
User Capacity:    319,936,615,424 bytes [319 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 3b
SATA Version is:  SATA 2.5, 3.0 Gb/s
Local Time is:    Sun Jun  7 00:12:11 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         ( 5768) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      (  99) minutes.
SCT capabilities:            (0x003f)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   051    -    0
  3 Spin_Up_Time            POS---   100   100   015    -    5504
  4 Start_Stop_Count        -O--CK   097   097   000    -    3967
  5 Reallocated_Sector_Ct   PO--CK   253   253   010    -    0
  7 Seek_Error_Rate         POSR--   253   253   051    -    0
  8 Seek_Time_Performance   P-S--K   253   253   015    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    3121
10 Spin_Retry_Count        PO--CK   253   253   051    -    0
11 Calibration_Retry_Count -O--C-   253   253   000    -    0
12 Power_Cycle_Count       -O--CK   097   097   000    -    3273
13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    1148040
187 Reported_Uncorrect      -O--CK   087   087   000    -    14
188 Command_Timeout         -O--CK   100   100   000    -    25
190 Airflow_Temperature_Cel -O---K   063   061   000    -    37
194 Temperature_Celsius     -O---K   124   121   000    -    38
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    1148040
196 Reallocated_Event_Count -O--CK   253   253   000    -    0
197 Total_Pending_Sectors   -O--C-   253   100   000    -    0
198 Offline_Uncorrectable   ----CK   253   253   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
200 Multi_Zone_Error_Rate   -O-R--   100   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   100   000    -    0
202 Data_Address_Mark_Errs  -O--CK   100   100   000    -    23
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Invalid Error Log index = 0x0000, trying reserved byte (0x06) instead
Device Error Count: 486 (device log contains only the most recent 8 errors)
    CR     = Command Register
    FEATR  = Features Register
    COUNT  = Count (was: Sector Count) Register
    LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
    LH     = LBA High (was: Cylinder High) Register    ]   LBA
    LM     = LBA Mid (was: Cylinder Low) Register      ] Register
    LL     = LBA Low (was: Sector Number) Register     ]
    DV     = Device (was: Device/Head) Register
    DC     = Device Control Register
    ER     = Error register
    ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 486 [5] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 01 00 00 00 61 5d 81 e0 00  Error: UNC at LBA = 0x00615d81 = 6380929

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 01 00 00 00 61 5d 81 e0 00     00:22:13.500  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:13.500  READ DMA EXT

Error 485 [4] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 02 00 00 00 61 5d 81 e0 00  Error: UNC at LBA = 0x00615d81 = 6380929

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 02 00 00 00 61 5d 81 e0 00     00:22:07.313  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 02 00 00 00 61 5d 7f e0 00     00:22:07.313  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 0f de 94 7d e0 00     00:22:07.313  READ DMA EXT
  42 ff ff 00 04 00 00 00 61 5d 83 e0 00     00:22:07.313  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:07.313  READ DMA EXT

Error 484 [3] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 04 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 04 00 00 00 61 5d 7f e0 00     00:22:02.125  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:02.125  READ DMA EXT
  42 ff ff 00 08 00 00 00 61 5d 87 e0 00     00:22:02.125  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:22:02.125  READ DMA EXT

Error 483 [2] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 08 00 00 00 61 5d 7f e0 00     00:21:56.000  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 10 00 00 00 61 5d 8f e0 00     00:21:55.938  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 0f de 94 7d e0 00     00:21:55.938  READ DMA EXT

Error 482 [1] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 10 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 10 00 00 00 61 5d 7f e0 00     00:21:50.750  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:50.750  READ DMA EXT
  42 ff ff 00 20 00 00 00 61 5d 9f e0 00     00:21:50.750  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:50.750  READ DMA EXT

Error 481 [0] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 20 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 20 00 00 00 61 5d 7f e0 00     00:21:45.875  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:45.875  READ DMA EXT

Error 480 [7] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 40 00 00 00 61 5d 7f e0 00  Error: UNC at LBA = 0x00615d7f = 6380927

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 40 00 00 00 61 5d 7f e0 00     00:21:41.375  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 40 00 00 00 61 5d 3f e0 00     00:21:41.375  READ VERIFY SECTOR(S) EXT
  42 ff ff 00 80 00 00 00 61 5d bf e0 00     00:21:41.313  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 0f de 94 7d e0 00     00:21:41.313  READ DMA EXT

Error 479 [6] occurred at disk power-on lifetime: 2281 hours (95 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 80 00 00 00 61 5d 3f e0 00  Error: UNC at LBA = 0x00615d3f = 6380863

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  42 ff ff 00 80 00 00 00 61 5d 3f e0 00     00:21:36.438  READ VERIFY SECTOR(S) EXT
  25 ff ff 00 01 00 00 00 00 00 00 e0 00     00:21:36.438  READ DMA EXT

SMART Extended Self-test Log (GP Log 0x07) not supported

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    38 Celsius
Power Cycle Min/Max Temperature:     37/38 Celsius
Lifetime    Min/Max Temperature:      3/38 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (68)

Index    Estimated Time   Temperature Celsius
  69    2020-06-06 22:05    35  ****************
...    ..(  6 skipped).    ..  ****************
  76    2020-06-06 22:12    35  ****************
  77    2020-06-06 22:13    36  *****************
  78    2020-06-06 22:14    36  *****************
  79    2020-06-06 22:15    36  *****************
  80    2020-06-06 22:16    35  ****************
...    ..(  2 skipped).    ..  ****************
  83    2020-06-06 22:19    35  ****************
  84    2020-06-06 22:20    36  *****************
  85    2020-06-06 22:21    35  ****************
...    ..(  9 skipped).    ..  ****************
  95    2020-06-06 22:31    35  ****************
  96    2020-06-06 22:32    36  *****************
  97    2020-06-06 22:33    36  *****************
  98    2020-06-06 22:34    35  ****************
  99    2020-06-06 22:35    35  ****************
100    2020-06-06 22:36    36  *****************
...    ..(  2 skipped).    ..  *****************
103    2020-06-06 22:39    36  *****************
104    2020-06-06 22:40    35  ****************
...    ..(  3 skipped).    ..  ****************
108    2020-06-06 22:44    35  ****************
109    2020-06-06 22:45    36  *****************
110    2020-06-06 22:46    36  *****************
111    2020-06-06 22:47    35  ****************
...    ..(  4 skipped).    ..  ****************
116    2020-06-06 22:52    35  ****************
117    2020-06-06 22:53    36  *****************
118    2020-06-06 22:54    35  ****************
119    2020-06-06 22:55    35  ****************
120    2020-06-06 22:56    35  ****************
121    2020-06-06 22:57    36  *****************
122    2020-06-06 22:58    35  ****************
...    ..( 38 skipped).    ..  ****************
  33    2020-06-06 23:37    35  ****************
  34    2020-06-06 23:38    33  **************
  35    2020-06-06 23:39    38  *******************
...    ..( 13 skipped).    ..  *******************
  49    2020-06-06 23:53    38  *******************
  50    2020-06-06 23:54    37  ******************
  51    2020-06-06 23:55    38  *******************
...    ..(  2 skipped).    ..  *******************
  54    2020-06-06 23:58    38  *******************
  55    2020-06-06 23:59    37  ******************
  56    2020-06-07 00:00    38  *******************
...    ..( 10 skipped).    ..  *******************
  67    2020-06-07 00:11    38  *******************
  68    2020-06-07 00:12    35  ****************

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC
0x8001  2            0  Vendor specific

Cz dysk się kończy ??