Problem z WiFi HP nc 8000

[arno]

0

witam, to pierwszy wątek, wiec prosze o wyrozumiałość i witam wszystkich.

brakuje jakiegos sterownika tylko nie wiem gdzie go szukac i pozniej jak wkomponowac do linuxa

komputer posiada klawisz do wlaczenia Wifi , ktory nie dziala. Na windowsie wszystko bylo ok

Kod:

System:
  Host: arno-HP-Compaq-nc8000 Kernel: 5.3.0-51-generic i686 bits: 32
  compiler: gcc v: 7.5.0 Desktop: Cinnamon 4.4.8
  Distro: Linux Mint 19.3 Tricia base: Ubuntu 18.04 bionic
Machine:
  Type: Laptop System: Hewlett-Packard product: HP Compaq nc8000 v: F.18
  serial: <filter>
  Mobo: Hewlett-Packard model: 088C v: 8051 Version 1E.19 serial: <filter>
  BIOS: Hewlett-Packard v: 68BAR Ver. F.18 date: 08/30/2006
Battery:
  ID-1: C137 charge: 9.9 Wh condition: 0.0/0.0 Wh (100%)
  model: Hewlett-Packard Primary status: Unknown
CPU:
  Topology: Single Core model: Intel Pentium M bits: 32 type: MCP
  arch: M Banias rev: 5 L2 cache: 1024 KiB
  flags: pae sse sse2 bogomips: 3189
  Speed: 800 MHz min/max: 600/1600 MHz Core speed (MHz): 1: 800
Graphics:
  Device-1: AMD RV350/M10 / RV360/M11 [Mobility Radeon 9600 / 9700]
  vendor: Hewlett-Packard NC8000 laptop driver: radeon v: kernel
  bus ID: 01:00.0
  Display: x11 server: X.Org 1.20.5 driver: ati,radeon
  unloaded: fbdev,modesetting,vesa resolution: 1400x1050~60Hz
  OpenGL: renderer: ATI RV350 v: 2.1 Mesa 19.2.8 direct render: Yes
Audio:
  Device-1: Intel 82801DB/DBL/DBM AC97 Audio
  vendor: Hewlett-Packard NC8000 laptop driver: snd_intel8x0 v: kernel
  bus ID: 00:1f.5
  Sound Server: ALSA v: k5.3.0-51-generic
Network:
  Device-1: Broadcom and subsidiaries BCM4306 802.11b/g Wireless LAN
  vendor: Hewlett-Packard driver: N/A port: 2000 bus ID: 02:04.0
  Device-2: Broadcom and subsidiaries NetXtreme BCM5705M_2 Gigabit Ethernet
  vendor: Hewlett-Packard NC8000 laptop driver: tg3 v: 3.137 port: 2000
  bus ID: 02:0e.0
  IF: enp2s14 state: up speed: 1000 Mbps duplex: full mac: <filter>
Drives:
  Local Storage: total: 37.26 GiB used: 13.29 GiB (35.7%)
  ID-1: /dev/sda vendor: Hitachi model: HTS548040M9AT00 size: 37.26 GiB
Partition:
  ID-1: / size: 36.42 GiB used: 13.29 GiB (36.5%) fs: ext4 dev: /dev/sda1
Sensors:
  Message: No sensors data was found. Is sensors configured?
Info:
  Processes: 171 Uptime: 2h 21m Memory: 927.9 MiB used: 656.0 MiB (70.7%)
  Init: systemd runlevel: 5 Compilers: gcc: 7.5.0 Shell: bash v: 4.4.20
  inxi: 3.0.32

[yahoob3]

0

Podaj wynik skryptu z tego poradnika: https://forum.linuxmint.pl/showthread.ph...78#pid1078

[omkar]

0

W przypadku problemów ze sterownikami do komputerów z systemem Linux, HP odsyła do tej strony: https://www.kernel.org/
Możesz też zapytać na forum:
https://h30434.www3.hp.com/
https://h30434.www3.hp.com/t5/Notebook-W...p/Internet

[yahoob3]

0

Coś cicho w wątku... taki trochę "bump"
Spróbowałbym takiej instalacji firmware: sudo apt-get install b43-fwcutter firmware-b43-installer i po zakończeniu restart.

[arno]

0

Dzięki panowie za szybka reakcje to działam ....

---

Dodano po pewnym czasie:

Podaj wynik skryptu z tego poradnika: https://forum.linuxmint.pl/showthread.ph...78#pid1078

Kod:

> ./wireless-info
--2020-05-07 07:18:22--  https://github.com/UbuntuForums/wireless-info/raw/master/wireless-info
Resolving github.com (github.com)... 140.82.118.3
Connecting to github.com (github.com)|140.82.118.3|:443... connected.
HTTP request sent, awaiting response... 302 Found
Location: https://raw.githubusercontent.com/UbuntuForums/wireless-info/master/wireless-info [following]
--2020-05-07 07:18:23--  https://raw.githubusercontent.com/UbuntuForums/wireless-info/master/wireless-info
Resolving raw.githubusercontent.com (raw.githubusercontent.com)... 199.232.40.133
Connecting to raw.githubusercontent.com (raw.githubusercontent.com)|199.232.40.133|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 17452 (17K) [text/plain]
Saving to: ‘wireless-info’

wireless-info       100%[===================>]  17,04K  --.-KB/s    in 0,02s   

Last-modified header missing -- time-stamps turned off.
2020-05-07 07:18:23 (887 KB/s) - ‘wireless-info’ saved [17452/17452]

Mam nadzieje ze oto chodziło

[yahoob3]

0

OK, skrypt wygenerował info, teraz nam je podaj
Jest w pliku "wireless-info" w katalogu domowym. Skopiuj zawartość pliku i wklej ja na forum, ale w znaczniki CODE, nie PHP