Zaloguj się

lexmark · 18-05-2020, 17:12

Witam

Mam problem z zamontowaniem (odpaleniem) udostępnionego urządzenia USB wpiętego w port routera.
Bez problemu wchodzę tam z Win 7/10, ponadto mogę podpiąć się w Mint poprzez domyślnego managera plików (wpisuję np smb://IP_serwera) i pokazuje się "folder z zawartością USB.
Natomiast każda próba zamontowania z konsoli kończy się błędem.

Kod:
sudo mount -t cifs -o user=guest //IP_Servera /home/marcin/mnt

Kod:
sudo mount.cifs -o user=guest //IP_Servera /home/marcin/mnt

Dodam, że domyślnie mam na routerze ustawiony folder dostępny dla każdego (public) nie pomaga nawet wprowadzenie userów i hasła.

W odpowiedzi dostaję pytanie o hasło dla "sudo", a następnie dla zasobu, choć nie mam tam hasła. Z Win wchodzę bez problemu, z managera plików w Mint, też, daję anonimowo i wyświetla zasób.
W odpowiedzi na w/w polecenia otrzymuję

Kod:
mount error(22): Invalid argument

Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) and kernel log messages (dmesg)

Z góry wielkie dzięki.
pozdrawiam
M.

***dedito*** · 18-05-2020, 17:26

0

Pokaż co widać:
smbclient -L //IP_Servera -U guest

lexmark · (Ten post był ostatnio modyfikowany: 18-05-2020, 17:42 przez dedito.)

0

(18-05-2020, 17:26)dedito napisał(a): Pokaż co widać:
smbclient -L //IP_Servera -U guest

Kod:
protocol negotiation failed: NT_STATUS_CONNECTION_DISCONNECTED

Takie info mam na routerze w USB Storage:

Cytat:Note:

1. Storage Sharing function is based upon the NetBIOS/SMB protocol supported by Windows OS and some additional operating systems.

2. Anonymous: All active volume(s) will be shared with no authentication required.

3. You will be able to access the shared folders by the following methods:

For Windows OS:Open the "Run" window within the Start menu and enter \\(IP Address) or \\(IP Address)\(Share Name)
e.g. \192.168.1.1 or \192.168.1.1photo;
For Mac OS:Open the "Connect to Server" window within the Go menu and enter smb://(IP Address) or smb://(IP Address)/(Share Name).
e.g. smb://192.168.1.1 or smb://192.168.1.1/photo.

***dedito*** · (Ten post był ostatnio modyfikowany: 18-05-2020, 17:47 przez dedito.)

0

Pokaż swoje smb.conf
i spróbuj tak: smbclient -L //IP_Servera/ --option='client min protocol=NT1'

lexmark · (Ten post był ostatnio modyfikowany: 18-05-2020, 17:55 przez lexmark.)

0

smb.conf, nie mam jak pokazać, bo tj na tp link ustawiony zasób.
po wklepaniu polecenia w terminal, otrzymałem zapytanie o hasło do WORKGROUP\marcin's - jakie hasło, nie mam bladego pojęcia.
Dobra po podaniu błędnego hasła mam :

Kod:
Server requested LANMAN password (share-level security) but 'client lanman auth          = no' or 'client ntlmv2 auth = yes'

tree connect failed: NT_STATUS_ACCESS_DENIED

Ale gdy dam ENTER:

Kod:
Sharename       Type      Comment

        ---------       ----      -------

        volume(sda1)    Disk

        IPC$            IPC       IPC Service (Samba Server)

        ADMIN$          IPC       IPC Service (Samba Server)

Reconnecting with SMB1 for workgroup listing.

        Server               Comment

        ---------            -------

        Workgroup            Master

        ---------            -------

***dedito*** · (Ten post był ostatnio modyfikowany: 18-05-2020, 17:57 przez dedito.)

0

Ja pisałem o twoim smb.conf czyli cat /etc/samba/smb.conf
Dopisz sobie tą opcję do swojego smb.conf i zrestartuj sambę lub komputer.

lexmark · 18-05-2020, 18:01

0

(18-05-2020, 17:56)dedito napisał(a): Ja pisałem o twoim smb.conf czyli cat /etc/samba/smb.conf
Dopisz sobie tą opcję do swojego smb.conf i zrestartuj sambę lub komputer.

Którą opcję?? Bo się pogubiłem.
smb.conf mam domyślny po instalce, nic tam nie grzebałem.

Kod:

#

# Sample configuration file for the Samba suite for Debian GNU/Linux.

#

#

# This is the main Samba configuration file. You should read the

# smb.conf(5) manual page in order to understand the options listed

# here. Samba has a huge number of configurable options most of which

# are not shown in this example

#

# Some options that are often worth tuning have been included as

# commented-out examples in this file.

#  - When such options are commented with ";", the proposed setting

#    differs from the default Samba behaviour

#  - When commented with "#", the proposed setting is the default

#    behaviour of Samba but the option is considered important

#    enough to be mentioned here

#

# NOTE: Whenever you modify this file you should run the command

# "testparm" to check that you have not made any basic syntactic

# errors.



#======================= Global Settings =======================



[global]



## Browsing/Identification ###



# Change this to the workgroup/NT-domain name your Samba server will part of

   workgroup = WORKGROUP



# server string is the equivalent of the NT Description field

   server string = %h server (Samba, Ubuntu)



#### Networking ####



# The specific set of interfaces / networks to bind to

# This can be either the interface name or an IP address/netmask;

# interface names are normally preferred

;   interfaces = 127.0.0.0/8 eth0



# Only bind to the named interfaces and/or networks; you must use the

# 'interfaces' option above to use this.

# It is recommended that you enable this feature if your Samba machine is

# not protected by a firewall or is a firewall itself.  However, this

# option cannot handle dynamic or non-broadcast interfaces correctly.

;   bind interfaces only = yes







#### Debugging/Accounting ####



# This tells Samba to use a separate log file for each machine

# that connects

   log file = /var/log/samba/log.%m



# Cap the size of the individual log files (in KiB).

   max log size = 1000



# We want Samba to only log to /var/log/samba/log.{smbd,nmbd}.

# Append syslog@1 if you want important messages to be sent to syslog too.

   logging = file



# Do something sensible when Samba crashes: mail the admin a backtrace

   panic action = /usr/share/samba/panic-action %d





####### Authentication #######



# Server role. Defines in which mode Samba will operate. Possible

# values are "standalone server", "member server", "classic primary

# domain controller", "classic backup domain controller", "active

# directory domain controller".

#

# Most people will want "standalone server" or "member server".

# Running as "active directory domain controller" will require first

# running "samba-tool domain provision" to wipe databases and create a

# new domain.

   server role = standalone server



   obey pam restrictions = yes



# This boolean parameter controls whether Samba attempts to sync the Unix

# password with the SMB password when the encrypted SMB password in the

# passdb is changed.

   unix password sync = yes



# For Unix password sync to work on a Debian GNU/Linux system, the following

# parameters must be set (thanks to Ian Kahan <<[email protected]> for

# sending the correct chat script for the passwd program in Debian Sarge).

   passwd program = /usr/bin/passwd %u

   passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .



# This boolean controls whether PAM will be used for password changes

# when requested by an SMB client instead of the program listed in

# 'passwd program'. The default is 'no'.

   pam password change = yes



# This option controls how unsuccessful authentication attempts are mapped

# to anonymous connections

   map to guest = bad user



########## Domains ###########



#

# The following settings only takes effect if 'server role = primary

# classic domain controller', 'server role = backup domain controller'

# or 'domain logons' is set

#



# It specifies the location of the user's

# profile directory from the client point of view) The following

# required a [profiles] share to be setup on the samba server (see

# below)

;   logon path = \\%N\profiles\%U

# Another common choice is storing the profile in the user's home directory

# (this is Samba's default)

#   logon path = \\%N\%U\profile



# The following setting only takes effect if 'domain logons' is set

# It specifies the location of a user's home directory (from the client

# point of view)

;   logon drive = H:

#   logon home = \\%N\%U



# The following setting only takes effect if 'domain logons' is set

# It specifies the script to run during logon. The script must be stored

# in the [netlogon] share

# NOTE: Must be store in 'DOS' file format convention

;   logon script = logon.cmd



# This allows Unix users to be created on the domain controller via the SAMR

# RPC pipe.  The example command creates a user account with a disabled Unix

# password; please adapt to your needs

; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u



# This allows machine accounts to be created on the domain controller via the

# SAMR RPC pipe.

# The following assumes a "machines" group exists on the system

; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u



# This allows Unix groups to be created on the domain controller via the SAMR

# RPC pipe.

; add group script = /usr/sbin/addgroup --force-badname %g



############ Misc ############



# Using the following line enables you to customise your configuration

# on a per machine basis. The %m gets replaced with the netbios name

# of the machine that is connecting

;   include = /home/samba/etc/smb.conf.%m



# Some defaults for winbind (make sure you're not using the ranges

# for something else.)

;   idmap config * :              backend = tdb

;   idmap config * :              range   = 3000-7999

;   idmap config YOURDOMAINHERE : backend = tdb

;   idmap config YOURDOMAINHERE : range   = 100000-999999

;   template shell = /bin/bash



# Setup usershare options to enable non-root users to share folders

# with the net usershare command.



# Maximum number of usershare. 0 means that usershare is disabled.

#   usershare max shares = 100



# Allow users who've been granted usershare privileges to create

# public shares, not just authenticated ones

   usershare allow guests = yes



#======================= Share Definitions =======================



# Un-comment the following (and tweak the other settings below to suit)

# to enable the default home directory shares. This will share each

# user's home directory as \\server\username

;[homes]

;   comment = Home Directories

;   browseable = no



# By default, the home directories are exported read-only. Change the

# next parameter to 'no' if you want to be able to write to them.

;   read only = yes



# File creation mask is set to 0700 for security reasons. If you want to

# create files with group=rw permissions, set next parameter to 0775.

;   create mask = 0700



# Directory creation mask is set to 0700 for security reasons. If you want to

# create dirs. with group=rw permissions, set next parameter to 0775.

;   directory mask = 0700



# By default, \\server\username shares can be connected to by anyone

# with access to the samba server.

# Un-comment the following parameter to make sure that only "username"

# can connect to \\server\username

# This might need tweaking when using external authentication schemes

;   valid users = %S



# Un-comment the following and create the netlogon directory for Domain Logons

# (you need to configure Samba to act as a domain controller too.)

;[netlogon]

;   comment = Network Logon Service

;   path = /home/samba/netlogon

;   guest ok = yes

;   read only = yes



# Un-comment the following and create the profiles directory to store

# users profiles (see the "logon path" option above)

# (you need to configure Samba to act as a domain controller too.)

# The path below should be writable by all users so that their

# profile directory may be created the first time they log on

;[profiles]

;   comment = Users profiles

;   path = /home/samba/profiles

;   guest ok = no

;   browseable = no

;   create mask = 0600

;   directory mask = 0700



[printers]

   comment = All Printers

   browseable = no

   path = /var/spool/samba

   printable = yes

   guest ok = no

   read only = yes

   create mask = 0700



# Windows clients look for this share name as a source of downloadable

# printer drivers

[print$]

   comment = Printer Drivers

   path = /var/lib/samba/printers

   browseable = yes

   read only = yes

   guest ok = no

# Uncomment to allow remote administration of Windows print drivers.

# You may need to replace 'lpadmin' with the name of the group your

# admin users are members of.

# Please note that you also need to set appropriate Unix permissions

# to the drivers directory for these users to have write rights in it

;   write list = root, @lpadmin

***dedito*** · (Ten post był ostatnio modyfikowany: 18-05-2020, 18:13 przez dedito.)

0

Tą którą dodawałaś do smbclienta.
Przykładowo, przed linijką #======================= Share Definitions =======================
Dopisz sobie jako root np. takie coś:

Kod:
#client min protocol (G) 

#This setting controls the minimum protocol version that the client will attempt to use.

client min protocol=NT1

Więcej: https://www.samba.org/samba/docs/current...INPROTOCOL

**yahoob3** · (Ten post był ostatnio modyfikowany: 18-05-2020, 18:26 przez yahoob3.)

0

A mnie coś się wydaje, że po //IP_Servera/ jeszcze coś może być w ścieżce Smile

U mnie, np. pendrive przedstawia się jako "a", czyli mam //IP_Servera/a

lexmark · 18-05-2020, 18:33

0

Kod:
#client min protocol (G)

#This setting controls the minimum protocol version that the client will attempt to use.

client min protocol=NT1

Dopisałem.
Zresetowałem sambę

Kod:
sudo service smbd restart

próba montowania:

Kod:
sudo mount -o user=guest //IP_servera /home/marcin/mnt/

Password for guest@//IP_servera:

mount error(22): Invalid argument

Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) and kernel log messages (dmesg)

Kod:
sudo mount.cifs -o user=guest //IP_servera/volume/ /home/marcin/mnt/

Password for guest@//IP_servera/volume/:

mount error(2): No such file or directory

Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) and kernel log messages (dmesg)

Tak, teoretycznie ma volume, ale w manager jak dam samo IP to podmontuje mi to bez problemu, a w terminalu za nic...

Zaloguj się
Login:
Hasło:	Nie pamiętam hasła
	Zapamiętaj mnie